Product ID:EA 9309 NA, PART A
MSDS Date:03/01/1992
FSC:8040
NIIN:01-126-6270
Kit Part:Y
MSDS Number: BRHBH

DEXTER HYSOL AEROSPACE INC DIV OF EXTER CORP

2850 WILLOW PASS ROAD
PITTSBURG, CA 94565-3237
US

Emergency Phone: 510-458-8000

Info Phone: 510-458-8000

Cage: 33564

DEXTER CORPORATION ADHESIVE & COATING SYSTEMS

312 BAY POINT, CA 94565-3299 US

Telephone: 202-483-7616

Cage: 33564

BISPHENOL A/EPICHLOROHYDRIN EPOXY RESIN (ORAL, RAT LD50

CAS: 25068-38-6

RTECS: KC2100000

Fraction By Weight: 60-100%

BUTADIENE-ACRYLONITRILE COPOLYMER

Fraction By Weight: 5-10%

SILICA

CAS: 112945-52-5

RTECS: VV7318000

Fraction By Weight: 1-5%

OSHA PEL 6 MG/M3

ACGIH TLV: 6 MG/M3

<10 G/L (ESTIMATE)

RTECS: 9999999VO

Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: BRIEF CONTACT MAY IRRITATE THE
SKIN OR CAUSE A RASH.

CHRONIC: REPEATED O R PROLONGED SKIN CONTACT MAY RESULT IN
ALLERGIC SENSITIZATION.
Effects of Overexposure:SKIN RASH, IRRITATION.
Medical Cond Aggravated by Exposure:SKIN SENSITIZATION.

First Aid:EYE: FLUSH EYES WITH WATER FOR 15 MINUTES. IF IRRITATION
PERSISTS, GET MEDICAL ATTENTION. SKIN: WASH SKIN THOROUGHLY WITH
SOAP AND WATER. IF IRRITATION PERSISTS, GET MEDICAL ATTENTION.
INHALATION: REM OVE VICTIM TO FRESH AIR. IF SYMPTOMS PERSIST, GET
MEDICAL ATTENTION. INGESTION: DRINK PLENTY OF WATER. GET MEDICAL
ATTENTION IMMEDIATELY.

Extinguishing Media:DRY CHEMICAL, HALON FIRE EXTINGUISHER, WATER SPRAY,
FOAM, OR FOG
Fire Fighting Procedures:WEAR SELF-CONTAIND BREATHING APPARATUS & FULL
PROTECT CLOTHES (TURN OUT GEAR). CARTRIDGE RESPIRATOR INADEQUATE
PROTECTION FOR FIRE FIGHTERS/EXOTHERM MITIGATION.
Unusual Fire/Explosion Hazard:MAY LIBERATE LARGE QUANTITIES OF DENSE
FOUL-SMELLING SMOKE WHICH MAY CONTAIN UNIDENTIFIED TOXIC GASSES.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES AND SAFETY
GLASSES. SCRAPE UP OR SHOVEL INTO DOT APPROVED WASTE CONTAINERS.

Handling and Storage Precautions:REFRIGERATED STORAGE IS RECOMMENDED TO
MAINTAIN PRODUCT QUALITY. THIS PRODUCT MAY BE STORED AT ROOM
TEMPERATURE (77F) FOR UP TO 12 MONTHS.
Other Precautions:FOLLOW CURING SCHEDULE AS RECOMMENDED IN PRODUCT
LITERATURE. DO NOT CUT, GRIND, WELD OR DRILL ON OR NEAR THIS
CONTAINER. SEE ALSO STABILITY SECTION IN MSDS.

Respiratory Protection:UNNECESSARY WITH ADEQUATE EXHAUST VENTILATION.
Ventilation:LOCAL EXHAUST VENTILATION AT POINT OF USE.
Protective Gloves:WEAR BUTYL RUBBER, PVC OR NITRILE RUBBER
Eye Protection:SAFETY GLASSES W/SIDE SHLDS,CHEM GOGGLES
Other Protective Equipment:AN EYEWASH AND SAFETY SHOWER SHOULD BE
NEARBY AND READY FOR USE.
Supplemental Safety and Health
KEY1:N1.

HCC:B3
Vapor Pres:NIL
Vapor Density:NIL
Spec Gravity:1.22 (WATER=1)
Viscosity:1500-6000 P
Solubility in Water:NEGLIGIBLE
Appearance and Odor:PEARLESCENT PASTE WITH PUNGENT ODOR

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:AVOID MIXING RESIN (PT A) & CURING AGENT
(PT B) IN BATCHES >1 LB UNLESS USED IMMED. DONT HEAT MIX >75F
UNLESS CURING *
Hazardous Decomposition Products:CO, NOX, ALDEHYDES, ACIDS AND
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:* SURFACES TO BE BONDED. FAILURE TO
OBSERVE PRECAUTIONS--EXCESSIVE HEAT BLDUP (EXOTHERM). EXOTHER MAY
RELEASE TOXIC GAS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.